Wood Polish Types: Melamine vs PU vs Duco vs Oil

Melamine, PU, duco and oil finishes compared: durability, look, cost and where each belongs, plus what is new in furniture finishing.

Sanjeev Khemka
By Sanjeev KhemkaUpdated 9 Nov 2026 · 4 min read
In this article
  1. Wood polish types compared
  2. What is new in finishing
  3. A good finishing schedule
  4. Frequently asked questions
  5. The bottom line

The four wood finishes used most in Indian furniture are melamine, PU (polyurethane), duco and oil. Melamine is the economical choice for indoor furniture; PU is tougher, clearer and the standard for good furniture and exteriors; duco is an opaque painted finish; and oil soaks into the wood for a natural look that is easy to repair. The right one depends on where the piece goes, how it will be used and how it should look.

Worker spraying clear PU lacquer on a wooden cabinet door in a finishing room

The short version:

  • Melamine: cheaper, good indoors, yellows and scratches more.
  • PU: hard, clear, water and heat resistant; best for dining tables, doors and exteriors (in exterior grade).
  • Duco: painted, opaque, glossy or matt; for MDF and coloured furniture.
  • Oil: natural look, easy to renew, needs regular care.

Wood polish types compared

MelaminePUDucoOil / hardwax oil
What it isAcid-catalysed lacquerTwo-pack polyurethane lacquerPigmented lacquer (NC or PU)Penetrating oils, sometimes with wax
LookClear, slight amberCrystal clear; matt to high glossSolid colourNatural, low sheen
DurabilityModerateHighModerate to highLow to moderate; renewable
Water and heatFairVery goodGoodFair
Exterior useNoExterior grades onlyLimitedYes, with UV oils
RepairHard to patchHard to patchRepaint the panelEasy: sand and re-oil
Best onIndoor furniture on a budgetTables, doors, kitchensMDF, painted furnitureOutdoor and natural pieces
Close-up of oiled teak bed corner

Where each belongs

On beds, wardrobes and shelving, melamine is adequate. On tables, kitchen fronts and anything handled every day, PU lasts noticeably longer. Duco suits painted, routed MDF such as fluted panels. Oil suits teak, walnut and oak that you want to look and feel like wood, and anything outdoors.

Specifying finishes for a project?

We finish furniture and millwork in PU, melamine, duco and oil to your sample. We respond within 24 hours.

Apply for a quote

What is new in finishing

Water-based coatings

Water-based PUs and acrylics have improved enough to match solvent-based finishes on many furniture uses, with far lower VOC emissions. They are standard for export to markets with strict indoor-air rules.

UV-cured finishes

Factory lines cure coatings in seconds under UV lamps instead of drying them for hours, which saves floor space and dust contamination. They suit flat panels, doors and flooring.

Automated spraying

Spray robots and reciprocating sprayers give an even film thickness and less overspray than hand spraying, and are now common in European and Asian furniture plants.

A good finishing schedule

  1. Sand through the grits to 180–240.
  2. Fill and stain if needed; open-pored woods like oak and ash need grain filler for a glass-smooth PU finish.
  3. Seal with a sanding sealer and denib.
  4. Top coat in two or three thin coats, sanding lightly between them.
  5. Finish all faces, including the underside and inside, so the piece takes up moisture evenly.

For the boards underneath, see MDF vs plywood vs HDHMR. For kitchen boards, use food-safe oil, not PU: see best wood for cutting boards. For doors, see main door designs.

Frequently asked questions

Which is better, PU or melamine?

PU is harder, clearer and more water- and heat-resistant. Melamine costs less and is fine for low-wear indoor furniture.

What is duco polish?

An opaque, painted lacquer finish, usually on MDF, available in any colour and gloss level.

Which polish is best for teak?

PU for a protected, clear finish; oil for a natural feel and easy repair, especially outdoors.

How long does PU polish last?

Indoors, many years with care; exterior PU needs recoating every few years depending on sun exposure.

Is PU polish safe indoors?

Once fully cured, yes. Water-based PUs give off far fewer fumes during application.

The bottom line

Use PU where wear and water are high, melamine where they are not, duco for colour on MDF, and oil for a natural, repairable finish. Browse our furniture and millwork.

Need a finish matched to a sample?

Send it to us and we will match it on your furniture or millwork. We respond within 24 hours.

Apply for a quote

Keep reading in Woodworking

Sanjeev Khemka

Sanjeev KhemkaWrites about timber, woodworking and trade for Kathwala, which supplies hardwood timber, plywood and panels and makes solid wood furniture and millwork to order. Questions? Get in touch.

Product Enquiry

Ask for a quote

Apply for a quoteWhatsApp