Wood Polish Types: Melamine vs PU vs Duco vs Oil
Melamine, PU, duco and oil finishes compared: durability, look, cost and where each belongs, plus what is new in furniture finishing.
In this article
The four wood finishes used most in Indian furniture are melamine, PU (polyurethane), duco and oil. Melamine is the economical choice for indoor furniture; PU is tougher, clearer and the standard for good furniture and exteriors; duco is an opaque painted finish; and oil soaks into the wood for a natural look that is easy to repair. The right one depends on where the piece goes, how it will be used and how it should look.

The short version:
- Melamine: cheaper, good indoors, yellows and scratches more.
- PU: hard, clear, water and heat resistant; best for dining tables, doors and exteriors (in exterior grade).
- Duco: painted, opaque, glossy or matt; for MDF and coloured furniture.
- Oil: natural look, easy to renew, needs regular care.
Wood polish types compared
| Melamine | PU | Duco | Oil / hardwax oil | |
|---|---|---|---|---|
| What it is | Acid-catalysed lacquer | Two-pack polyurethane lacquer | Pigmented lacquer (NC or PU) | Penetrating oils, sometimes with wax |
| Look | Clear, slight amber | Crystal clear; matt to high gloss | Solid colour | Natural, low sheen |
| Durability | Moderate | High | Moderate to high | Low to moderate; renewable |
| Water and heat | Fair | Very good | Good | Fair |
| Exterior use | No | Exterior grades only | Limited | Yes, with UV oils |
| Repair | Hard to patch | Hard to patch | Repaint the panel | Easy: sand and re-oil |
| Best on | Indoor furniture on a budget | Tables, doors, kitchens | MDF, painted furniture | Outdoor and natural pieces |

Where each belongs
On beds, wardrobes and shelving, melamine is adequate. On tables, kitchen fronts and anything handled every day, PU lasts noticeably longer. Duco suits painted, routed MDF such as fluted panels. Oil suits teak, walnut and oak that you want to look and feel like wood, and anything outdoors.
We finish furniture and millwork in PU, melamine, duco and oil to your sample. We respond within 24 hours.
What is new in finishing
Water-based coatings
Water-based PUs and acrylics have improved enough to match solvent-based finishes on many furniture uses, with far lower VOC emissions. They are standard for export to markets with strict indoor-air rules.
UV-cured finishes
Factory lines cure coatings in seconds under UV lamps instead of drying them for hours, which saves floor space and dust contamination. They suit flat panels, doors and flooring.
Automated spraying
Spray robots and reciprocating sprayers give an even film thickness and less overspray than hand spraying, and are now common in European and Asian furniture plants.
A good finishing schedule
- Sand through the grits to 180–240.
- Fill and stain if needed; open-pored woods like oak and ash need grain filler for a glass-smooth PU finish.
- Seal with a sanding sealer and denib.
- Top coat in two or three thin coats, sanding lightly between them.
- Finish all faces, including the underside and inside, so the piece takes up moisture evenly.
For the boards underneath, see MDF vs plywood vs HDHMR. For kitchen boards, use food-safe oil, not PU: see best wood for cutting boards. For doors, see main door designs.
Frequently asked questions
Which is better, PU or melamine?
PU is harder, clearer and more water- and heat-resistant. Melamine costs less and is fine for low-wear indoor furniture.
What is duco polish?
An opaque, painted lacquer finish, usually on MDF, available in any colour and gloss level.
Which polish is best for teak?
PU for a protected, clear finish; oil for a natural feel and easy repair, especially outdoors.
How long does PU polish last?
Indoors, many years with care; exterior PU needs recoating every few years depending on sun exposure.
Is PU polish safe indoors?
Once fully cured, yes. Water-based PUs give off far fewer fumes during application.
The bottom line
Use PU where wear and water are high, melamine where they are not, duco for colour on MDF, and oil for a natural, repairable finish. Browse our furniture and millwork.
Send it to us and we will match it on your furniture or millwork. We respond within 24 hours.
Keep reading in Woodworking
- Furniture, Design and Woodworking Exhibitions 2026–27: Global and India CalendarEvery major furniture, interiors, woodworking machinery and timber trade fair from November 2026 to November 2027, in India…
- Chest of Drawers Buying Guide: Sizes, Woods and Joinery That LastsHow to choose or specify a chest of drawers: standard sizes, the best woods, drawer joinery and runners,…
- Charcuterie Boards: Best Woods, Sizes and How to Care for ThemHow to choose a charcuterie board: the best woods, sizes by guest count, shapes, food-safe finishes and care,…
- Best Wood for Cutting Boards (and Which to Avoid)The best and worst woods for cutting boards, end grain vs edge grain, what the research says about…
